View MAX8863-D_2957959.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2002 august, 2002 rev. 2 1 publication order number: max8863/d max8863 pin-compatible, low-dropout, 120 ma linear regulator delivering up to 120 ma, the max8863 is a fixed output, lowdropout linear regulator that operates from a +2.5 v to +6.0 v input range. the 50 m a supply current remains independent of load, making these devices ideal for batteryoperated portable equipment. the output of the max8863 is preset at 3.15 v, 2.84 v, 2.80 v or 1.80 v. (other output voltage options are available contact on semiconductor for more information.) the max8863 is pincompatible with the maxim max8863 ldo and is available in the sot235 package. features ? low cost ? pincompatible with max8863 ? stable with any type of capacitors ? low, 55 mv dropout voltage @ 50 ma i out ? low, 50 m a operating supply current (even in dropout) ? 140 m sec (typ.) turnon response time from shdn ? low, 350 m v rms output noise ? miniature external components ? thermal overload protection ? output current limit ? lowpower shutdown mode applications ? cordless, pcs, and cellular telephones ? pcmcia cards ? modems ? handheld instruments ? palmtop computers ? electronic planners figure 1. typical application c out 1 m f + battery shdn gnd gnd in out c in 1 m f output voltage sot23 euk suffix case 1212 1 pin connections 2 3 4 5 see detailed ordering and shipping information in the package dimensions section on page 9 of this data sheet. ordering information see general marking information in the device marking section on page 9 of this data sheet. device marking information 5 1 2 4 3 shdn out gnd in gnd (top view) http://onsemi.com
max8863 http://onsemi.com 2 absolute maximum ratings* rating symbol value unit input voltage 6.5 v output shortcircuit duration infinite set to gnd 0.3 to +6.5 v shdn to gnd 6.5 to + 6.5 v shdn to in 6.5 to + 0.3 v output voltage 0.3 to v in + 0.3 v continuous power dissipation (t a = +70 c) sot235 (derate 7.1 mw/ c above +70 c) 571 mw operating temperature range t a 40 to 85 c storage temperature range t stg 65 to +160 c lead temperature (soldering, 10 sec.) +300 c esd withstand voltage human body model (note 1) v esd 2000 v latchup performance (note 2) positive negative i latchup 420 240 ma *stresses above those listed under aabsolute maximum ratings'' may cause permanent damage to the device. these are stress ratin gs only and functional operation of the device at these or any other conditions above those indicated in the operational sections of th e specifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. electrical characteristics (v in = +3.6 v, gnd = 0 v, t a = t min to t max , unless otherwise specified. typical values are at t a = +25 c.) (note 3) characteristics test conditions symbol min typ max unit input voltage (note 4) v out 2.5 v v out = 1.8 v v in v out + 0.5 v 2.7 6.0 6.0 v output voltage 0 ma i out 50 ma t s r q v out 3.05 2.75 2.70 1.745 3.15 2.84 2.80 1.80 3.25 2.93 2.88 1.85 v maximum output current i out 120 ma current limit (note 5) i lim 280 ma input current i out = 0 i in 50 90 m a dropout voltage (note 6) i out = 1.0 ma i out = 50 ma i out = 100 ma 1.1 55 110 120 240 mv line regulation v in = v out + 0.5 v to 6.0 v i out = 1.0 ma v lnr 0.10 .001 0.10 %/v load regulation i out = 0 ma to 50 ma v ldr 0.01 0.040 %/ma output voltage noise 10 hz to 1.0 mhz c out = 1.0 m f c out = 100 m f 350 220 m v rms wake up time (from shutdown mode) v in = 3.6 v c in = 1.0 m f, c out = 1.0 m f i l = 30 ma, (see fig. 1) t wk 10 m sec settling time (from shutdown mode) v in = 3.6 v c in = 1.0 m f, c out = 1.0 m f i l = 30 ma, (see fig. 1) t s 140 m sec 1. tested to eia/jesd22a114a 2. tested to eia/jesd78 3. limits are 100% production tested at t a = +25 c. limits over the operating temperature range are guaranteed through correlation using statistical quality control (sqc) methods. 4. guaranteed by line regulation test. 5. not tested. for design purposes, the current limit should be considered 150 ma minimum to 410 ma maximum. 6. the dropout voltage is defined as (v in v out ) when v out is 100 mv below the value of v out for v in = v out + 2.0 v.
max8863 http://onsemi.com 3 electrical characteristics (continued) (v in = +3.6 v, gnd = 0 v, t a = t min to t max , unless otherwise specified. typical values are at t a = +25 c.) (note 7) characteristics test conditions symbol min typ max unit shutdown shdn input threshold v ih v il 2.0 0.4 v shdn input bias current v shdn = v in t a = +25 c t a = t max i shdn 0 50 100 na shutdown supply current v out = 0 v t a = +25 c t a = t max i qshdn .002 0.02 1.0 m a shutdown to output discharge delay c out = 1.0 m f, no load to 10% of v out 1.0 msec thermal protection thermal shutdown temperature t shdn 170 c thermal shutdown hysteresis t shdn 20 c 7. limits are 100% production tested at t a = +25 c. limits over the operating temperature range are guaranteed through correlation using statistical quality control (sqc) methods. pin description pin number symbol description 1 shdn activelow shutdown input. a logic low reduces the supply current to 0.1 na. a logic low also causes the output voltage to discharge to gnd. connect to in for normal operation. 2 gnd ground. this pin also functions as a heatsink. solder to large pads or the circuit board ground plane to maximize thermal dissipation. 3 in regulator input. supply voltage can range from +2.5 v (+2.7 v for v out = 1.8 v) to +6.0 v. bypass with 1.0 m f to gnd (see capacitor selection and regulator stability ). 4 out regulator output. sources up to 120 ma. bypass with a 1.0 m f, 1.0 w typical esr capacitor to gnd. 5 gnd connect to gnd.
max8863 http://onsemi.com 4 detailed description the max8863 is a fixed output, lowdropout, lowquiescent current linear regulator designed specifically for portable, batteryoperated equipment such as cellular phones, cordless phones, and modems. a 1.20 v reference, error amplifier, mosfet driver, pchannel pass transistor, comparator, and internal feedback voltage divider comprise the max8863 (see figure 3). the bandgap reference is connected to the error amplifier's inverting input. the error amplifier then compares the reference with the selected feedback voltage and amplifies the difference. the mosfet driver, reading the error signal, applies the correct drive to the pchannel pass transistor. if the feedback voltage is lower than the reference, the passtransistor is pulled lower to allow more current through, and to increase the output voltage. conversely, if the feedback voltage is higher than the reference, the passtransistor is pulled up, which allows less current through to the output. turn on response the turn on response is defined as two separate response categories, wake up time (t wk ) and settling time (t s ) . the max8863 has a fast wake up time (10 m sec typical) when released from shutdown. see figure 2 for the wake up time designated as t wk . the wake up time is defined as the time it takes for the output to rise to 2.0% of the v out value after being released from shutdown. v out shdn v il t wk 98% 2% t s v ih figure 2. wake up response time the total turn on response is defined as the settling time (t s ) , see figure 2. settling time (inclusive with t wk ) is defined as the condition when the output is within 2.0% of its fully enabled value (140 m sec typical) when released from shutdown. the settling time of the output voltage is dependent on load conditions and output capacitance on v out (rc response). internal pchannel pass transistor featuring a 1.1 w pchannel mosfet pass transistor, the max8863 offers longer battery life than similar designs using pnp pass transistors, which waste current in dropout when the pass transistor saturates. pnpbased regulators also use high basedrive currents under large loads. the pchannel mosfet, however, does not require a base drive current, which reduces quiescent current. the max8863 uses only 50 m a of quiescent current. shdn + mos driver with i limit thermal sensor 1.2 v ref shutdown logic in gnd gnd out p n (max8863 only) figure 3. functional block diagram
max8863 http://onsemi.com 5 shutdown low input on shdn shuts down the max8863 by turning off the pass transistor, control circuit, reference, and all biases. this reduces the supply current to 0.1 na, typical. for normal operation, connect shdn to in. when the max8863 is placed in shutdown mode, the output voltage is actively discharged to ground. current limit the current limiter on the max8863 monitors and controls the pass transistor's gate voltage. it estimates the output current, limiting it to 280 ma. the current limit should be considered 150 ma (min) to 410 ma (max) for design purposes. the output can be shorted to ground indefinitely without damaging the device. thermal overload protection the max8863 features thermal overload protection, which limits total power dissipation. the thermal sensor signals the shutdown logic to turn off the pass transistor when the junction temperature exceeds t j = +170 c. this allows the ic's junction temperature to cool by 20 c before the thermal sensor turns the pass transistor back on. this results in a pulsed output during continuous thermal overload conditions. this feature is designed to protect the max8863 during thermal events. high load currents and high inputoutput differential voltages may cause a momentary overshoot of 2.0% to 8.0% for 200 msec when the load is removed. this can be avoided by raising the minimum load current from 0 m a (+125 c) to 100 m a (+150 c). the maximum junction temperature rating of +150 c should not be exceeded for continuous operation. operating region and power dissipation the max8863's maximum power dissipation depends on the thermal resistance of the case and circuit board, the rate of air flow, and the temperature difference between the die junction and ambient air. the devices' power dissipation is p = i out (v in v out ); resulting maximum power dissipation is: p max (t j t a ) ja where (t j t a ) is the temperature difference between the devices' die junction and the surrounding air, and ja is the thermal resistance of the chosen package to the surrounding air. the devices' gnd pin provides an electrical connection to ground and channels heat away. the gnd pin should be connected to ground with a large pad or ground plane. applications information capacitor selection and regulator stability a 1.0 m f capacitor on the input, and a 1.0 m f capacitor on the output should generally be used on the max8863. for better supplynoise rejection and transient response, larger input capacitor values and lower esr should be used. if the device is several inches from the power source or if large, fast transients are expected, a highervalue input capacitor (10 m f) may be required. using large output capacitors may improve loadtransient response, stability, and powersupply rejection. a minimum of 1.0 m f is recommended for stable operation over the full temperature range with load currents up to 120 ma. noise during normal operation, the max8863 have low (350 m v rms ) output noise. the adc's powersupply rejection specifications should be considered for applications that include analogtodigital converters of greater than 12 bits. powersupply rejection and operation from sources other than batteries powersupply rejection for the max8863 is 62 db at low frequencies, rolling off above 300 hz. power supply noise rejection is primarily controlled by the output capacitor at frequencies of more than 20 khz. supply noise rejection and transient response can be improved when operating from sources other than batteries by increasing the values of the input and output capacitors, and using passive filtering techniques. load transient considerations with the max8863, typical overshoot for step changes in the load current from 0 ma to 50 ma is 12 mv. to lessen transient spikes, increase the output capacitor's value, and decrease its esr. inputoutput (dropout) voltage a regulator's dropout voltage determines the lowest usable supply voltage. this determines the useful endoflife battery voltage for batterypowered systems. since the max8863 uses a pchannel mosfet pass transistor, the devices' dropout voltage is a function of r ds(on) multiplied by the load current.
max8863 http://onsemi.com 6 0.06 40 0.02 25 line regulation (%) 0.10 figure 4. line regulation vs. temperature figure 5. output voltage vs. temperature figure 6. load regulation vs. temperature figure 7. load regulation vs. temperature temperature ( c) load regulation (%) figure 8. dropout voltage vs. temperature 0.10 3.50 v to 5.50 v temperature ( c) 0.06 0.02 70 85 figure 9. output noise vs. frequency 0 v out , output voltage (v) temperature ( c) load regulation (%) temperature ( c) frequency (khz) noise ( m v/ /hz) 0.00 1 0.01 10 1.0 0.1 0.0 10.0 100 1000 temperature ( c) r load = 50 m c out = 1 m f 0.04 0.04 0.08 0.08 0.00 2.91 40 2.83 25 2.75 2.79 2.87 70 85 0 2.89 2.81 2.93 2.77 2.85 v out set/1.0 ma @ 3.5 v (v) 0.030 40 0.010 25 0.040 0.000 0.020 70 85 0 0.025 0.005 0.035 0.015 0 to 50 ma 0 to 100 ma 0.030 0.010 0.040 0.000 0.020 0.025 0.005 0.035 0.015 40 25 70 85 0 dropout voltage (v) 0.12 40 0.04 25 0.00 0.08 70 85 0 0.10 0.02 0.06 50 ma 0 to 50 ma typical characteristics
max8863 http://onsemi.com 7 10 10 k 1 k 100 100 mvpp figure 10. power supply rejection ratio figure 11. shutdown transient response figure 12. shutdown transient response figure 13. line response figure 14. wake up response time v out = 2.84 v r load = 50 w 28.4 k w frequency (khz) 100 k 1 m 10 m c out = 1 m f ch2 gnd 200 m sec/div ch1 gnd ch1 gnd ch2 gnd 200 m sec/div time (100 m s/div) output, shutdown voltage (v) 134 25 2.8 v shdn v out 6 3 v 0 v v in = 3.6 v i load = 30 ma c in = 1 m f c load = 1 m f 200 m sec/div ch1 gnd ch2 gnd 0 v t = 25 c c in = 1 m f c l = 1 m f r l = shdn = 0 v shdn v out = 0.5 v/div xshdn = 3 v no overshoot xshdn = 0 v c in = 1 m f c out = 1 m f r l = 100 w v in = 3.5 v v out = 0 v turn on time = 150 m s v out = 2.7 v v in = 4.5 v v in = 3.5 v v outac 20 m v/div typical characteristics ch1 ch2 c in = c out = 1 m f r l = 470 w xshdn = 3.5 v
max8863 http://onsemi.com 8 w device marking device marking pin 1 user direction of feed component taping orientation for 5pin sot23 devices standard reel component orientation tr suffix device (mark right side up) sot23 package carrier width (w) pitch (p) part per full reel reel size 8 mm 4 mm 3000 7 inches carrier tape, number of components per reel and reel size reverse reel component orientation rt suffix device (mark upside down) pin 1 user direction of feed p
max8863 http://onsemi.com 9 and = two letter part number codes + temperature range and voltage = year and quarter code = lot id number marking diagram 12 3 4 12 3 4 ordering information device output voltage* marking and 2 1 package junction temperature range shipping max8863qeukt max8863reukt max8863seukt max8863teukt 1.80 2.80 2.84 3.15 g4 g3 g2 g1 sot23 40 c to +85 c 3000 tape & reel *other output voltages are available. please contact on semiconductor for details.
max8863 http://onsemi.com 10 package dimensions sot23 euk suffix case 121201 issue o dim min max millimeters a1 0.00 0.10 a2 1.00 1.30 b 0.30 0.50 c 0.10 0.25 d 2.80 3.00 e 2.50 3.10 e1 1.50 1.80 e 0.95 bsc e1 1.90 bsc l l1 0.45 0.75 notes: 1. dimensions are in millimeters. 2. interpret dimensions and tolerances per asme y14.5m, 1994. 3. datum c is a seating plane. a 1 5 23 4 d e1 b l1 e e e1 c m 0.10 c s b s a b 5x a2 a1 s 0.05 c l 0.20 ---
max8863 http://onsemi.com 11 notes
max8863 http://onsemi.com 12 on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and s pecifically disclaims any and all liability, including without limitation special, consequential or incidental damages. atypicalo parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating parameters, including atypicalso must be validated for each customer application by customer's technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indem nify and hold scillc and its of ficers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and re asonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized u se, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employ er. publication ordering information japan : on semiconductor, japan customer focus center 291 kamimeguro, meguroku, tokyo, japan 1530051 phone : 81357733850 email : r14525@onsemi.com on semiconductor website : http://onsemi.com for additional information, please contact your local sales representative. max8863/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 3036752175 or 8003443860 toll free usa/canada fax : 3036752176 or 8003443867 toll free usa/canada email : onlit@hibbertco.com n. american technical support : 8002829855 toll free usa/canada

▲Up To Search▲

Price & Availability of MAX8863-D

	To Download MAX8863-D Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .